When a garage door keypad stops working, the cause is usually a dead battery, a keypad that has lost its pairing with the opener, or one worn-out button in your code. Start with a fresh battery (most keypads take a 9-volt), then reprogram the keypad to the opener. If your remotes have stopped working too, the problem is the opener, not the keypad.
We’re All Access Garage Doors, a family-owned company that repairs garage door openers, keypads and remotes for homes in San Diego, Los Angeles, the Bay Area, Houston and Austin. Here’s how to find the cause in a few minutes, what you can safely fix yourself, and when a new keypad or a technician makes more sense.
Why does a garage door keypad stop working?
Most of the time it’s one of four things:
- A weak or dead battery. This is the most common cause by far.
- Lost programming. This often happens after a power outage or a battery change.
- A worn button. One number in your code stops registering.
- Signal interference. It can come from the wall the keypad is mounted on, or from electronics near the opener.
Less often, the keypad itself has failed after years of sun and weather, or the opener’s radio receiver has a fault.
Is it the keypad or the opener?
Try your remote and the wall button inside the garage first. The keypad and the remotes talk to the opener by radio, but the wall button is wired. Craftsman, which makes garage door openers, explains that these work independently, so it’s normal for one to work while another doesn’t.
- Wall button and remotes work, keypad doesn’t: the problem is the keypad. Keep reading.
- Wall button and keypad work, remotes don’t: check lock mode (below).
- Wall button works, but neither remotes nor keypad do: the opener’s radio receiver may be at fault. That’s a job for a technician.
- Nothing works, wall button included: the opener may have no power. See what to check when a garage door won’t open.
- Remotes and keypad work, wall button doesn’t: the wall button or its wire is the likely cause.
How do you know if the keypad battery is dead?
Press a button and watch the keypad’s light. If it’s dim, flickers or doesn’t come on at all, replace the battery. Most keypads take a 9-volt battery, and some older models use a 12-volt, according to Craftsman. The battery usually sits under a cover on the front or bottom of the keypad.
If the battery is new and the keypad still won’t open the door, reprogram it (below). Some keypads lose their pairing when the battery comes out.
While the cover is open, look at the battery contacts. Near the coast in San Diego, Los Angeles and the Bay Area, damp salt air can corrode them, and Houston’s humidity does the same. Summer sun on a south- or west-facing wall, from El Cajon to Austin, is hard on the plastic. You can clean off light corrosion. A keypad with cracked or faded buttons is usually due for replacement.
Does lock mode turn off the keypad?
On LiftMaster and Chamberlain openers, no. Many of their wall buttons have a lock feature that switches off the remotes, but by design the keypad and the wall button keep working (LiftMaster’s owner’s manual says so). So if your keypad opens the door and your remotes don’t, lock mode is the likely reason. A blinking light on the wall button often means it’s on. On many models, you turn it off by holding the lock button for a couple of seconds.
Other brands handle lock mode differently, so check your opener’s manual.
How do you reprogram a garage door keypad?
Pair it with the opener again, using the Learn button on the motor unit. The steps vary by brand, so check the label on the motor or your opener’s manual. On most LiftMaster and Chamberlain openers it works like this:
- Find the Learn button on the motor unit, usually on the back or side near the antenna, sometimes under the light cover. Use a sturdy step ladder.
- Press and release it. Don’t hold it down: holding the Learn button for about six seconds erases every remote and keypad paired to the opener.
- Enter your code on the keypad, then press and hold Enter until the opener’s lights blink or you hear a click. Do this while the Learn light is still on; it stays lit for a short time.
- Test the keypad from outside with the door in view.
If it won’t pair, the keypad may not be compatible with your opener’s radio system. Check the opener’s brand and model number before you buy a new one.
What if only some of the numbers work?
Program a completely different code and try that. Craftsman suggests this test: if the new code works, one of the buttons in your old code has worn out. You can keep the new code or replace the keypad. Keypads used several times a day wear out the same few buttons first.
One more to rule out: if you set up a temporary code for a guest or a dog walker, those can expire. On Craftsman keypads, an expired temporary code can still close the door but won’t open it.
Can something block the keypad’s signal?
Yes. Craftsman notes that the surface a keypad is mounted on can interfere with its signal. Its fix is to take the keypad off the wall and test it. If it works in your hand, remount it with rubber grommets or a small piece of wood behind it.
LED bulbs in or near the opener can also interfere with remotes and keypads. If the trouble started after you changed the opener’s bulbs, try a bulb made for garage door openers.
When should you replace a garage door keypad?
When a fresh battery and reprogramming don’t fix it, the buttons are cracked or worn, or the case lets water in. A new keypad has to match your opener’s brand and radio system, so note the model number on the motor unit first.
If your opener is so old that no current keypad will pair with it, that’s usually a sign the opener is near the end of its life. Our guide to whether to repair or replace a garage door opener walks through that decision.
Should you change your keypad code?
Yes, if you’ve just moved in, a contractor or former roommate knows the code, or you can’t remember who you’ve given it to. Skip easy codes like 1234, your house number or a birth year. Your opener’s manual shows how to change it. On many models it uses the same Learn-button steps as reprogramming.
And if your door has been opening on its own, a stuck keypad button is one possible cause. See why a garage door opens by itself.
When should you call a garage door technician?
Call when the keypad still won’t work after a new battery and reprogramming, when the remotes have stopped working too, or when the door itself is struggling, noisy or stopping partway. A keypad fault can’t damage the door. But a door that strains or reverses has a different problem, often a spring, and springs are never a do-it-yourself job.
All Access Garage Doors repairs and replaces garage door openers, keypads and remotes in five areas. Call the number for yours:
- San Diego County: (833) 537-1818
- Los Angeles: (833) 537-1818
- Bay Area: (925) 644-6522
- Houston: (833) 537-1818
- Austin: (512) 885-7411
In San Diego, see our garage door opener repair page. Every garage door inspection we do includes a check of the wall button, remotes and keypad. For a gate keypad, see gate repair.
Frequently asked questions
Usually a dead battery, lost pairing or a worn button. The keypad has its own battery and its own pairing with the opener, so a working remote tells you the opener is fine. Replace the battery first, then reprogram the keypad.
Most take a 9-volt battery. Some older models use a 12-volt. The battery is usually under a cover on the front or bottom of the keypad.
Press and release the Learn button on the opener, then enter your code on the keypad and hold Enter until the opener’s lights blink. Don’t hold the Learn button down: on many openers that erases every remote and keypad.
Yes. Buttons wear out, and years of sun and moisture damage the case and battery contacts. If a new battery and reprogramming don’t help, replace the keypad.
Not on LiftMaster or Chamberlain openers. Their lock feature switches off the remotes but leaves the keypad and wall button working. If your remotes have stopped but the keypad still works, check the lock button on the wall.
By the All Access Garage Doors team. Updated November 2026.
